Library of climate resources

This standard establishes a consistent methodology for performing geotechnical site investigations so that the results can be used to design building foundations with due consideration, in a risk management framework, of the conditions prevailing at the building site, including: the distinctive characteristics of permafrost; and the seasonal and interannual climate conditions as well as the projected climate conditons over the service life of the building foundations.

The purpose of this Standard is to provide requirements for the inspection and monitoring of erosion and sediment control measures installed on construction sites. Compliance with this Standard will allow users to demonstrate that erosion and sediment control measures are installed where they should be, functioning as expected, and that every reasonable effort is being made to prevent impacts to the environment and infrastructure surrounding the construction site. This Standard specifies minimum requirements for the inspection of ESC measures throughout the duration of a construction project, as well as requirements and recommendations for monitoring certain water quality parameters. It also includes a description of the required qualifications for a qualified erosion and sediment control inspector (QESCI) and a QESCI in-training (QESCI-IT). This Standard further details the required documentation and communication procedures to be followed with respect to erosion and sediment control inspection, monitoring, and other compliance measures. This Standard provides a) defined experience and education requirements for those considered to be qualified to perform the tasks outlined; b) the minimum requirements for the inspection of ESC measures and plan implementation; c) the minimum requirements, as well as recommendations, for water monitoring to determine ESC measure performance; and d) the minimum requirements for documenting compliance with an ESC plan.

This Standard specifies the minimum planning, design, and maintenance requirements for community drainage systems in Canada's northern communities. The purpose of this Standard is to increase the capacity of communities and individuals to prepare and implement effective community drainage plans. These plans address both existing and anticipated drainage management challenges arising from deficiencies in past practices, as well as the need to adapt to future changes in climate.

CSA A440.2 applies to the determination of energy performance properties for a variety of fenestration systems, including fixed windows, operable windows, sliding glass doors, hinged doors, skylights with flat glazings, and curtain walls. In addition, CSA A440.2 provides a means for determining a comparative Energy Rating (ER) for fixed and operable windows, sliding doors, and hinged doors to be used in low-rise residential housing. CSA A440.3, the user guide to CSA A440.2, has been prepared to explain the content and use of CSA A440.2. CSA A440.3 allows the knowledgeable user to develop specific energy performance properties that apply to fenestration systems of different sizes in specific geographic locations and orientations.

This Standard sets forth methods for both new installation and replacement installation of factory assembled windows, exterior doors, and skylights that are intended for installation in low-rise buildings and buildings used primarily for, but not limited to, residential occupancy where the windows, doors, and skylights (including window wall) are R, LC, or CW class within the application of AAMA/WDMA/CSA 101/I.S.2/A440. This Standard provides minimum requirements for the installation of fenestration products including windows, doors, and skylights. This Standard addresses issues that could compromise the performance of the fenestration product as established by testing to the requirements of AAMA/WDMA/CSA 101/I.S.2/A440. Where installation methods are not specifically addressed in this Standard or in the installation instructions of the manufacturer of a fenestration product, a design professional should be consulted for a solution consistent with the intent of the minimum requirements and principles in this Standard.

This Supplement is for use in conjunction with AAMA/WDMA/CSA 101/I.S.2/A440-17 and contains additional requirements for Canada. This Supplement provides simplified methods to calculate the minimum performance levels for resistance to water penetration, wind loads, and snow loads for fenestration products on buildings in Canada.X375

For 90 years, the Canadian Electrical Code, Part I has been developed and updated to help better protect electrical workers and promote improved consistency in electrical installations across the country. Now in its 25th edition, the CSA C22.1:21, Canadian Electrical Code, Part I includes over 200 additions and revisions, including: · Changes to hazardous location requirements. · New content addressing energy storage systems and climate change adaptation. · Rules for functionally grounded renewable energy systems.

This Standard, which forms part of the Canadian Electrical Code, Part III provides requirements for overhead systems and includes electric supply and communication circuits that are installed alone, in joint use, or in proximity to each other or other facilities. This Standard presents a choice between deterministic and reliability-based design methods. Reliability based design methods are covered by CSA C22.3 No. 60826. Additions to the Overhead Systems Standard address climate adaptation, including for flooding, weather loadings, discontinuous permafrost, and ice removal management systems.

This Standard, which forms part of the Canadian Electrical Code, Part III, covers the requirements for construction of underground systems and includes electric supply and communication circuits that are installed alone, in joint use, or in proximity to each other or other facilities. New clauses have been included that deal with flooding and ground movement to address climate change.

The environmental impacts of greenhouse gas (GHG) emissions are driving many organizations to create initiatives to reduce their carbon footprints. This standard details the requirements for designing, developing, managing and reporting GHG inventories. It also includes requirements and guidance on inventory quality management, reporting, internal auditing and the organization’s responsibilities in verification activities.